From project review and material verification to SMT assembly, inspection, testing, documentation, and shipment, every board follows a controlled path from design intent to working product.
6-stage floor journeySMT + through-holeInspection + test
Every printed circuit board assembly has a path. Before a finished board is tested, packed, and shipped, it moves through a series of controlled steps: documentation review, material verification, setup, assembly, inspection, test, and final release.
At Micron, that journey is built around high-mix, low-volume electronics manufacturing for OEMs that need responsive communication, careful documentation, and reliable execution. From prototypes and NPI builds to repeat production runs, the goal is the same: move each assembly through the floor with the right information, the right controls, and the right checks in place.
The Journey Map
Six stages from incoming project to finished assembly
The exact path may vary by build type, but most PCB assemblies move through the same disciplined sequence: plan the build, verify the kit, assemble the board, inspect workmanship, confirm performance, and prepare the finished product for shipment.
01
Review & Launch
Confirm the BOM, revision, assembly files, quantities, schedule, test notes, and special requirements before the job reaches the floor.
02
Materials & Kit Check
Verify incoming components, bare boards, stencils, hardware, consigned materials, and customer-supplied documentation.
03
SMT Assembly
Print solder paste, place components, and run reflow with controlled setup, placement data, and process documentation.
04
Secondary Operations
Complete through-hole assembly, hand soldering, labeling, mechanical hardware, coating, or other customer-specific steps.
05
Inspection & Test
Use AOI, X-ray as needed, visual review, programming, ICT, flying-probe, or functional test according to the build plan.
06
Final Release
Close out documentation, verify labels and packaging, review test records, and prepare the assembly for delivery.
01
Project review and build planning
A successful build starts before the first component reaches the production floor. The project package is reviewed to understand the scope of the assembly, including the BOM, Gerbers or ODB++ files, pick-and-place data, assembly drawings, quantities, schedule, and any special requirements.
Confirm current revision across BOM, PCB files, drawings, firmware, and test instructions.
Review DFM questions around placement, solderability, polarity markings, panelization, and test access.
Create a build plan so the floor has clear instructions instead of assumptions.
02
Materials receiving and kit verification
Once materials arrive, they are checked against the build requirements. For turnkey builds, this includes purchased components, bare boards, stencils, and required hardware. For consigned or hybrid builds, customer-supplied materials are received, identified, and compared against the BOM and documentation.
Verify part numbers, quantities, revisions, alternates, and substitutions.
Identify missing, damaged, unclear, ESD-sensitive, or moisture-sensitive materials.
Protect the production schedule by catching kit issues before setup begins.
03
SMT setup, solder paste printing, placement, and reflow
For surface-mount assemblies, the process typically begins with solder paste printing. The stencil, paste, board support, and printer setup work together to apply the correct amount of solder paste to each pad. Components are then placed according to the centroid data and carried through reflow to form solder joints.
Accurate placement data helps reduce setup time and prevent orientation issues.
Profile-tuned reflow supports reliable solder joints across mixed component sizes and thermal masses.
04
Through-hole assembly and secondary operations
Many assemblies are not SMT-only. Connectors, terminals, transformers, relays, switches, large capacitors, labels, mechanical hardware, and other odd-form components may require through-hole assembly or secondary processing.
Complete hand soldering, selective operations, mechanical assembly, labeling, masking, or coating as specified.
Review orientation, lead trim, solder fillet quality, spacing, and mechanical fit.
Use clear work instructions to keep manual operations consistent.
05
Inspection, programming, and electrical test
Inspection confirms that the assembly was built as intended, while electrical test confirms that it performs as expected. Depending on the product, this may include AOI, X-ray, visual inspection, firmware programming, ICT, flying-probe, functional test, calibration, or customer-specific verification.
X-ray may be used for hidden joints such as BGAs, QFNs, or bottom-terminated components.
Programming and test records can support traceability, troubleshooting, and repeat builds.
06
Final inspection, documentation review, packaging, and shipment
Before shipment, the assembly goes through final checks. This may include final visual inspection, cleaning review, label verification, packaging review, test record confirmation, and documentation closeout.
Gather required reports, certificates, programming logs, inspection images, or other records.
Use ESD-safe packaging, labels, serialization, protective packaging, or customer-specific handling instructions.
Protect the finished product so it reaches the customer in the condition expected.
Why It Matters
Reliability is built through the entire process
A PCB assembly does not become reliable at one single step. Reliability is built through the entire journey, from clear data and disciplined material control to inspection, testing, documentation, and final release.
Clear files reduce interpretation risk.
Kit checks prevent avoidable production delays.
Setup discipline supports repeatable assembly.
Inspection catches workmanship issues early.
Testing confirms real product behavior.
Documentation supports traceability and future builds.
Related Micron Capabilities
Explore the services behind the journey
Each step in the floor journey connects to a core Micron EMS capability.
IPC standards help define quality, reliability, and consistency expectations across electronics manufacturing.
When you send a build to an EMS partner, you are not just buying assembly time. You are relying on a process.
At Micron, that process is designed to support high-mix, low-volume electronics builds with disciplined documentation, careful workmanship, inspection, testing, and responsive communication from start to finish.
Whether the project is a prototype, pilot build, or repeat production run, the journey through the floor is where design intent becomes a working product.
